The hazards of droplet in compressed air!
The condensed water occurring in the compressed air pipes with the changes in pressure and temperature move in the compressed air line. If no measures are taken, these droplets can lead to serious problems such as corrosion in the pneumatic systems, air leaks valve seizures etc. In order to prevent such problems, the compressed air-liquid water must be separated using a high efficiency cyclone water separator.
Working principle
A large amount of water-containing steam enters the steam-water separator and moves downward in a centrifugal manner.The entrained water is separated due to the decrease in speed; the separated liquid flows through the trap and is discharged, and the dry and clean steam is discharged from the gas water separator outlet is discharged.
Where Refrigerated Water Separator be installed among the compressed system?
The gas water separator is used in a compressed air system, located after the water-cooled chiller to separate moisture from the compressed and refrigerated air and after its exit, the air passes through an air dryer containing molecular sieve and activated alumina. We strongly suggest Water-Gas Separator to be installed, after air tank, before Refrigerated Air Dryer, Cyclone water-air separator also can installed inside of the air compressor.
Feature & Benefit
A. High liquid removal efficiencies at all flow conditions
B. Protects coalescing filters from bulk liquid contamination.
C. Helps provide air quality in accordance with ISO 8573-1:2001 the international
standard for compressed air quality
D. Suitable for all compressed air applications
E. Suitable for all compressor types, including variable flow
F. Low pressure losses for low operational costs
G. Low lifetime costs
H. All FWS water separators are covered by a 15 year housing guarantee.
Technical Specification
The flow rate below is the treatment capacity of compressed air under rated working pressure 7 barg (100psi g). For the application in other working pressure, please refer to the correction factors.
| Model | Pipe size | Flow rates | Dimension (mm) |
| L/S | m³/min | scfm | W(Width) | D(Depth) | H(Height) |
| WS 15 | RC1/2" | 40.0 | 2.4 | 84.5 | 89 | 79 | 228 |
| WS 25 | RC3/4" | 60.0 | 3.6 | 127.1 | 89 | 79 | 228 |
| WS 50 | RC1" | 75.0 | 4.5 | 158.9 | 89 | 79 | 263 |
| WS 75 | RC1" | 125.0 | 7.5 | 264.8 | 120 | 110 | 335 |
| WS 100 | RC1-1/2" | 166.7 | 10.0 | 353.1 | 120 | 110 | 335 |
| WS 200 | RC2" | 300.1 | 18.0 | 635.6 | 164 | 151 | 564 |
| WS 250 | RC2-1/2" | 416.8 | 25.0 | 882.8 | 164 | 151 | 664 |
| WS 700 | RC2-1/2" | 700.0 | 42.0 | 1483.1 | 200 | 189 | 712 |
| WS 800 | RC3" | 833.5 | 50.0 | 1765.6 | 200 | 189 | 712 |
| WS 800F | DN80/DN100 | 833.5 | 50.0 | 1765.6 | 280 | 189 | 734/744 |
| WS 1000F | DN100/DN125 | 1000.2 | 60.0 | 2118.7 | 280 | 189 | 780/795 |
| WS 1200F | DN100/DN125 | 1166.7 | 70.0 | 2464.0 | 280 | 189 | 1058/1073 |
| Technical requirements | Maximum operating pressure: 10 barg Operating temperature:1.5~ 80°C |
| Pressure | Barg | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 |
| Psig | 15 | 29 | 44 | 59 | 73 | 87 | 100 | 116 | 131 | 145 | 160 | 174 | 189 | 203 | 219 | 232 |
| Correction factor | 0.38 | 0.53 | 0.65 | 0.76 | 0.85 | 0.93 | 1.00 | 1.07 | 1.13 | 1.19 | 1.23 | 1.31 | 1.36 | 1.41 | 1.46 | 1.51 |
Success Cases
